Re: Printer taking to long to start
If not using the pcl5 drivers, load them and see if it improves. This is now a very old printer with limited memory so pcl6 and postscript will take a long time.
View Article64 bit(Win 7) print drivers(HPLJ3800dtn) on a 32 bit print server(2003)
There has to be a document explaining how to make this work, right?
View ArticleHP Color LaserJet Enterorise M750n Optional Trays
Dear, I bought QTY: 10 HP Color LaserJet Enterorise M750n (D3L08A) and also bought for each printer two optional trays (CE860A). In the scond page of the attached brochure, you will find that I can add...
View ArticleGhost-printer
One of the users has a 'ghost-printer' installed which can't be removed (P4515 Upd PCL6). One of the troubles is that the driver used disturbes the proper functioning of an other printer (laserjet...
View ArticleHP3525n EIO card Status not ready
HiWe have a HP3525n which has lost its IP address. Ive tried a power cycle and waiting for 5 minutes for it to reconnect. Swapped out Cat 5 cables. Still no joy. Config page says I/O card Not Ready and...
View ArticleRe: HP3525n EIO card Status not ready
This printer has an embedded nic card and a slot for an add in EIO jet direct card. I have seen this once and the printer needed installation of a EIO network card. On the one we had, the green light...
View ArticleRe: Ghost-printer
Your post is really confusing. If you can not delete the printer which is very strange, then I would just go into the properties of the ghost printer driver and under device settings go to installed...
View ArticleRe: HP3525n EIO card Status not ready
Hi Thanks for the replyTo clarify the card that is in came with the printer and has been working for a couple of years at least.Regards Tim
View ArticleRe: LaserJet 2605dn "79 Error"
It would not print internal printer reports from the control panel. This is after sitting power on for days but mostly idle. After sitting off for two days I could print internal reports from the...
View ArticleRe: CP4525 colors not aligned
Good morning David, thanks for responding to my post and apologies for not responding sooner. Anyway, I performed the NVRAM reset and there was no change in the issue. One question, after performing...
View ArticleRe: CP1525n 79 Error
Hello, 79 error code is equivialent to the 49 error code. I would clear the print job and try sending a print job from different applications. The issue is caused by the browser, if you go to print...
View ArticleHP m603dn printer
A customer reported error on printer after power outage due to electrical storm. When printer was powered on it displayed error 49.23.38 . After researching the only thing I could find was to disable...
View ArticleLaserjet 2430 - Universal HP Driver has no 1200 DPI Support
Using the latest download from the HP Site, (dated January 2014 i think), the printer does not allow for any printing higher then 600 DPI now. Not that it REALLY makes a difference, but its annoying...
View ArticleRe: Laserjet 2430 - Universal HP Driver has no 1200 DPI Support
In an addition to this, i see HP has a "Administraton" Pack that you can download that has a bunch of utilities in it.. one of them lets you Edit the driver package to select the 1200 DPI settings.....
View ArticleRe: Laserjet 4250 & 1200dpi for Universal Printing
Just so you know, i have a post open for this exact issue with a LJ 2430DTN. I do the auto config and no 1200 options are listed as well.. Only 600DPI, using the latest 5.8 Driver. Something is wrong...
View ArticleRe: Upgraded firmware on LJ P4515x and now it says resend upgrade
Did you resend the firmware after clearing the error? If not, remove all accessories (tray 3, duplexer, envelope feeder) and perform the firmware upgrade. Wait until it finishes and the printer comes...
View ArticleRe: HP3525n EIO card Status not ready
Since yours in the "N" model you really do not have a card, but a network interface which is part of the formatter just like the usb port on the formatter.
View ArticleRe: CP4525 colors not aligned
Did you perform the 3rd item in the attachment. The attachment also contains just a plain factory reset and hard disk reset which you do not need. It is the third item and the screen needs to say NVRAM...
View ArticleConnectivity for a HP Color Laserjet 3000n
I have a Optiplex 9020 running Windows 7 and I'm trying to connect it to my HP Color Laserjet 3000n. It should be running through a USP port. Can't get it to do anything. Any ideas?? Thanks ct_
View ArticleRe: Double sided printing with HP Laserjet 5000 DN Not working on Windows 7...
You need to go into the properties of the driver and under device settings go to installable options and change duplex from not installed to installed. The default for all hp drivers is duplex not...
View Article