Re: Laser Jet Pro 400 color M475dn- Touch Screen Freeze
You need to calibrate the touch screen. Common issue. See link below, I could not find hp instructions but just go down in the link to where you press both sides at the same...
View ArticleRe: printer not responding to queries
THIS Problem is KILLING ME(Obviously 'Old-School' & Just ONE CLICK from being a Computer Genius), and 20+ Years of PageMaker 6.5 Business Files! (If not Bad Enough, Apple-'The Leaders'- Made Sure...
View ArticleRe: printer not responding to queries
>THIS is THE Official 'HP Forum'? This is a peer to peer forum, not an official HP support site.Have you tried contacting the HPSC, if the product is still under warranty?http://www.hp.com/go/hpsc...
View ArticleRe: printer not responding to queries
I am not a Mac Person, but I have one question. Did you press the green button on your LJ1200 to see if it prints a test page? If it does not, then I would assume you have a hardware issue with the...
View ArticleRe: printer not responding to queries
Thanks David & Dennis for your quick response! Only have the 'Ready-to-Go' single Green light ON, and when pushed; prints out Test Page just fine. I'll check the info you've sent, but hopefully my...
View Articledriver for hp laserjet 1012 printer ( window 8 )
I could not find the driver for window 8 . How do I find the alternative driver for this laserjet 1012 printer for windeow 8?
View ArticleRe: Hp Laser Jet P3015 cutting of last two lines of Document
If you run a config page from the menu on the printer does it print ok to include the bar code at the bottom. If not you are having an issue with the set registration setting. You could try a cold...
View ArticleRe: LJ 2420dn Cold Reset
Just in case someone is still searching for the solution,...1. Power on the printer.2. Once you see the RAM counts, press and hold down the green check button until all three lights are on.3. Proceed...
View ArticleRe: HP P3005 Grinding Noise from the FUSER
This method stops the grinding noise but when you print it. The paper jams right when it goes inside the fuser which means the gear is not spinning at a faster speed.
View ArticleRed dots in vertical line with an HP printer
When I print using a color application ( Word or other color application ) I receive a vertical line of red dots 2" in from the left side of the paper and they are about 1 inch apart. If I print from...
View ArticleRe: Red dots in vertical line with an HP printer
If it happens only in one color then odds are the toner cartridge is defective.
View ArticleBar Chart in PCL5
Hi All! Does anybody know how to make bar (or pie) charts using PCL5 code? Thanks in advance.
View ArticleRe: need the installer of hp laserjet1010
Dear all,kindly find me a way to install software of lj 1010 to download ,i can t afford buying a new printer..appreciate your co operation
View ArticleRe: Bar Chart in PCL5
You can draw filled rectangles using the appropriate PCL Rectangular Area Fill escape sequences. For drawing pie sections, you'd be better off looking at the HP-GL/2 commands (HP-GL/2 is a subset of...
View ArticleRe: Red dots in vertical line with an HP printer
Thanks but can you tell me what color cartridge would control the RED dots ??
View ArticleRe: HP P3005 Grinding Noise from the FUSER
Hello, what is the jam code? Also, how does the roller look in tray 2?
View Articlelaser jet CM1415fnw
making grinding noise while printing also printing horizontal black lines on copy sometimes horizontal lines almost completely cover copy
View ArticleRe: Need HP to document WHICH fonts are available for PCL5, 5e, 5c printing...
So far no go. The twitter support referred me back to the phone support then stopped responding when I told them I'd already gone that route repeatedly.I sent a web online support request Friday with a...
View Article