I have read all the posts about the HP4700 causing dots from printing labels. I have had this happen three times now. I just found out it is caused by using other name brand labels. If I purchase HP labels, will this problem still happen?
I can't afford to purchase toner when I need to print labels. As of now, I refuse to print labels.
If I can use HP brand labels without this issue, then I will start printing labels again.
Thanks..
Sue
where do I buy HP labels? I can't seem to find any online.
Perfectly good laserjet 1000 cannot be used with a windows 8 computer/laptop due to the lack of a device driver. Should be a way to make this work.
The paper keeps jammimg in the rear door section.
Dear Support,
I have an HP LaserJet M602 but when I print with a custom font on this printer it fails.
The prints are completely different then the custom fonts.
I tried to add the fonts 3 .otf file and 1 .ttf file but i can't upload it to the printer.
The printer only wants PCM/PFM font files.
How can i convert my fonts to this type? Or how can I solve this problem?
Kind regards,
Leon Portenge
Have you tried to use the universal driver or the Windows 7 driver?
Don't know the answer (I have no access to LaserJet M602 models), just a few comments:
Power off the printer. Remove one cartridge. Power back on. You should now be able to upgrade or downgrade firmware if needed. Once completed power off and reinsert cartridge.
To get around this error and update your firmware, remove atleast one toner cartridge. You should be able to boot the printer and not run into the error. If you are unable to find an IP address, you may need to set a manual IP and then access the web interface. Update the firmware and then reinstall cartridge.
There are a bunch of other topics with solutions to the same problem:
http://h30499.www3.hp.com/t5/Printers-LaserJet/Extra-Page-print/m-p/5936041
>So maybe the Webmaster will see this
Wow! That's unexpected!
If you want to report this, please create a new topic in the Community Feedback & Suggestions board:
http://h30499.www3.hp.com/t5/Community-Feedback-Suggestions/bd-p/community-feedback-suggestions
When my HP Touchsmart (Win 7) machine bit the dust, I ordered a new HP ENVY 700 series Win 7 Machine. I downloaded the full solution software for my HP CM2320nf Laser printer, and tried to re-install the software on the new machine. The software instalation hung, and even waiting over night didn't help. I believe it was because the all of the Windows updates had not been installed.
After rebooting and waiting for the rest of the Windows updates, I tried to re-install the software again. I can select what type of CM2320nf printer I have (Fax Model), but when I click on Install software, the entire program crashes, and disappears off the screen.
I have rebooted, Cleaned the registry, checked for spyware/Adware, ran my antivirus software, downloaded the package from a diffrent (Trusted) source, and everything else I could think of. The software still crashes off the screen. I installed the seperate printer drivers, but cannot get the software for the scanner installed. I need that up and running on my new HP machine. Does anybody have any Idea why the softare keeps crashing, or what I can do to get it to install? Is there a way to download the scanner software seperatly? If I have posted in the wrong area, let me know. This topic seemed the closest to my current problem.
I'm in the same boat. Bought new toners $400, but not new enough to take back. Entre said it needs a new formatter board, but hard to find one. Also, they would charge 2 hrs time to replace, which probably equals $200 to n$300. If I can replace it, I'll try to do it myself.
How do I turn off the "Low Toner" alerts?
Thanks,
Keith
Yes...somewhere. Will check.
Here is my visual answer to the question.
Look at the two boxes. Lets say that they are a sqare inch (just magnified).... Don't worry about the lines, those just helped me create the image.
The one on the left, notice how there is more total white space than the one on the right.. The left box represents "4 dpi" (or 4 dots per inch), and the right one represents "16 dpi". Imagine those same circles, aka dots, being even smaller. Lets say so small you cant even see them anymore. Can you see how all the white space would be gone?
What makes the white space disappear? That would be ink / tonor. So, with this being said, I came to the conclusion that a lower dpi would INDEED use less ink / toner. Yes, the circles are bigger, but there are less of them.
-------------------
and to your comment "...it will save toner because the colors will be printed lighter." It will not be necessarily be printed lighter, it will just look lighter due to all that white space between the dots
-------------------
I have problems regarding the duplex printing.
CLJ CP2025dn with actual firmware
Win 8.1 64-Bit
Word 2013 64-Bit
Since a few days i can not use the duplex printing. The printer prints first, second and third site (using duplex) and says then "cleaning" and then "failure print". When I clicked "OK" the printer starts again with site 3, prints 3 more sites (using the duplex) and then same as on the beginning and so on.
I tried to use three actual drivers:
upd-pcl5-x64-5.7.0.16448
upd-ps-x64-5.8.0.17508
upd-pcl6-x64-5.8.0.17508
On a second computer (WIN 7 64-Bit + Word 2013 64-Bit) in the same network it works.
Joerg
Hello, also other things to look for when it comes to 49 error codes, is make sure the firmware is up to date, as well as, I have noticed while using IE it can cause the 49 error, only if you select print from the toolbar icon. If you click the print hyperlink on the website, it will convert the page to a printable version of the page you want to print.
Just some extra info on this issue.....
